HOSES & PIPES.. 2000

3.0 LITER TWIN-TURBO. FRONT SECTION.

3.0 LITER TWIN-TURBO. FRONT SECTION. inlet. Lower. PartQualifier: inlet. Reservoir hose.

3.0 LITER TWIN-TURBO. FRONT SECTION. outlet. PartQualifier: outlet. Reservoir hose. Upper.

3.0 LITER TWIN-TURBO. FRONT SECTION. inlet.

3.0 LITER TWIN-TURBO. FRONT SECTION. outlet.

3.0 LITER TWIN-TURBO. auxiliary inlet. FRONT SECTION.

3.0 LITER TWIN-TURBO. auxiliary outlet. FRONT SECTION.

3.0 LITER TWIN-TURBO. FRONT SECTION.

3.0 LITER TWIN-TURBO. FRONT SECTION.

3.0 LITER TWIN-TURBO. FRONT SECTION. PartQualifier: w/o quad zone. Pipe assy. w/o quad zone.

3.0 LITER TWIN-TURBO. FRONT SECTION. PartQualifier: w/quad zone. Pipe assy. w/quad zone.

3.0 LITER TWIN-TURBO. FRONT SECTION. 6 x 1mm. A Nut used to retain the Fuse and Relay Center to it's mounting point. A Nut which attaches the ignition module to it's mounting point. A Nut which attaches the water pump to it's mounting surface. A solid metal or plastic block with a threaded hole in the Center which is used to secure the Keyless Entry Control Module to it's mounting point. A solid metal or plastic block with a threaded hole in the Center which is used to tighten or adjust the ABS Hydraulic Control Unit. A solid metal or plastic block with a threaded hole in the Center which is used to tighten or adjust the Active Suspension Control Module. A solid metal or plastic block with a threaded hole in the Center which is used to tighten or adjust the Backup Sensing System Module. A solid metal or plastic block with a threaded hole in the Center which is used to tighten or adjust the Body Control Module. A solid metal or plastic block with a threaded hole in the Center which is used to tighten or adjust the Brake Master Cylinder Reservoir. A solid metal or plastic block with a threaded hole in the Center which is used to tighten or adjust the Cruise Control Distance Sensor. A solid metal or plastic block with a threaded hole in the Center which is used to tighten or adjust the Engine Coolant Expansion Tank. A solid metal or plastic block with a threaded hole in the Center which is used to tighten or adjust the Exhaust Manifold Heat Shield. A solid metal or plastic block with a threaded hole in the Center which is used to tighten or adjust the Quarter Panel. Air Filter Housing Nut. Audio Amplifier Nut. Battery Hold Down Nut. Battery Tray Washer. Bumper Cover Reinforcement Nut. Bumper Guide Nut. Bumper Splash Shield Nut. Door Mirror Nut. Door Sill Plate Nut. Engine Air Intake Hose Nut. Engine Air Intake Resonator Nut. Engine Control Module Nut. Engine Coolant Pipe Seal. Fender Insulator Nut. Junction block mounting Nut. Mud Flap Nut. Nut to secure Bumper Cover. Nut used to mount headlight. Part cannot be reused/reinstalled. Power Brake Booster Nut. Radiator Mount Nut. Radiator Support Tie Bar Nut. Radio Nut. Seat Back Frame Nut. Spoiler Nut. Washer Fluid Reservoir Nut. Included with: Lower Bracket, Rear Spoiler.

3.0 LITER TWIN-TURBO. FRONT SECTION. Pipe assy clip.

3.0 LITER TWIN-TURBO. FRONT SECTION. Reservoir tank bracket.

3.0 LITER TWIN-TURBO. FRONT SECTION. Reservoir tank.

3.0 LITER TWIN-TURBO. FRONT SECTION. Reservoir tank bolt. A Bolt which attaches the quarter panel to it's mounting point. A threaded rod with a drive head (such as hex, 12 point, torx, etc) on one end used to secure the Battery Cable Battery Terminal End to a mounting point. A threaded rod with a drive head on one end used to secure the Curtain Air Bag Inflator Module to its mounting point. Air Bag Control Module Bolt. Engine Coolant Reservoir Bolt. GPS Navigation Control Module Bolt. Horn Mount Bolt. Interior Grab Bar Bolt. Quarter Panel Splash Shield Bolt. Quarter Panel Splash Shield Screw. Radio Antenna Bolt. Included with: Head Air Bag, WindShield pillar trim.

3.0 LITER TWIN-TURBO. FRONT SECTION. Reservoir cap. A cover that prevents foreign debris from entering the container. Engine Cooling. Location-Reservoir. Primary. Radiator Cap. Side. Included with: Radiator Assembly, Reservoir Assembly.